ผลการค้นหา

ค้นเจอ 112 รายการ

Unit Water Content

(Concrete Engineering) The quantity of water per unit volume of freshly mixed concrete, often expressed as gallons or pounds per cubic yard. This is the quantity of water on which the water cement ratio is based, and does not include water absorbed by the aggregate

Blow Back

(english) A coating defect consisting of a lower coating film weight on the bottom of the coated sheet caused by high velocity air in the oven. Blow back usually occurs with high solids coatings which have little solvent to evaporate and "set" the film.

Linear Elastic:

(english) A force-displacement relationship which is both linear and elastic. For a structure, this means the deformation is proportional to the loading, and deformations disappear on unloading. For a material, the concept is the same except strain substitutes for deformation, and stress substitutes for load.

Mixing Speed

(Concrete Engineering) Rate of mixer drum rotation or that of the paddles in a pan, open-top, or trough type mixer, when mixing a batch; expressed in revolutions per minute (rpm) or in peripheral] feet per minute of A point on the circumference at maximum diameter.

Pressure:

(english) Pressure is a similar idea to stress, the force intensity at a point, except that pressure means something acting on the surface of an object rather than within the material of the object. When discussing the pressure within a fluid, the meaning is equivalent to stress.

Support:

(english) A support contributes to keeping a structure in place by restraining one or more degrees of freedom. In a structural model, supports represent boundary entities which are not included in the model itself, e.g., foundations, abutments, or the earth itself. For each restrained translation degree of freedom at a support, there is a corresponding reaction force; for each restrained rotation degree of freedom, there is a reaction moment.

Bloom 2

(english) A semi-finished hot rolled product, rectangular in cross section, produced on a blooming mill. For iron and steel, the width is not more than twice the thickness, and the cross-sectional area is usually not less than 36 sq. in. Iron and steel blooms are sometimes made by forging.

Section Modulus:

(english) A property of a cross sectional shape, which depends on shape, and orientation. Section modulus is usually denoted S, and S = I/c, where I = moment of inertia about an axis through the centroid, and c is the distance from the centroid to the extreme edge of the section.

Age Hardening

(english) Hardening by aging, usually after rapid cooling or cold working. The term as applied to soft, or low carbon steels, relates to a wide variety of commercially important, slow, gradual changes that take place in properties of steels after the final treatment. These changes, which bring about a condition of increased hardness, elastic limit, and tensile strength with a consequent loss in ductility, occur during the period in which the steel is at normal temperatures.

Slip Form

(Concrete Engineering) A form which is raised or pulled as concrete is placed; may move vertically to form wails, stacks, bins or silos, usually of uniform cross section from bottom to top; or a generally horizontal direction to lay concrete evenly for highways, on slopes and inverts of canals, tunnels, and siphons.

Moist Room

(Concrete Engineering) A room used for storing and curing cementitious test specimens. The atmosphere of this room is maintained at a temperature of 73.4 3.0'F or 23.0*1.7'0 and relative humidity of at least 98 percent. These facilities must be adequate to continually maintain free moisture on the exteriors of test specimens.

Burr

(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด