ผลการค้นหา

ค้นเจอ 119 รายการ

Bent Axis Pumps

(english) In this pump, the pistons are at an angle to the drive shaft and Thrust Plate. The piston block shaft is connected to the drive shaft by a universal joint, not shown. The drive shaft, thrust plate, piston block shaft, and piston block all revolve. The connecting rods are attached to the thrust plate and revolve with it, unlike the swash plate pump where the piston rods slide past a stationary swash plate. The outlet ports are semi-circular holes in the Valve Plate, shown on the far right of the animation on edge and in a head-on view below, right. As the pump revolves, half the pistons suck in fluid as they pass over the intake port. The other pistons discharge their fluid through the outlet port. This pump should be compared to the radial piston pump, swash plate pump, and wobble pump.

Inelastic:

(english) Not surprisingly, the opposite of elastic. A deformation of a structure or material under load is described as inelastic when the deformation remains after the load is removed. The term plastic is often used with the same meaning.

Brinell Hardness

(english) The hardness of a metal or part, as represented by the number obtained from the ratio between the load applied on the spherical area of the impression made by a steel ball forced into the surface of the material tested.

Bearing Strength

(english) The maximum bearing load at failure divided by the effective bearing area. In a pinned or riveted joint, the iffective area is calculated as the product of the diameter of the hole and the thickness of the bearing member.

Balanced Steel

(english) Steels in which the deoxidisation is controlled to produce an intermediate structure between a rimmed and killed steel, Sometimes referred to as semi-killed steels, they possess uniform properties throughout the ingot and amongst their applications are boiler plate and structural sections.

Particle-Size Distribution

(Concrete Engineering) Particle distribution of granular materials among various sizes; for concrete material normally designated as gradation. Usually expressed in terms of cumulative percentages smaller or larger than each of a series of sieve openings or percentages between certain ranges of sieve openings.

Unit Water Content

(Concrete Engineering) The quantity of water per unit volume of freshly mixed concrete, often expressed as gallons or pounds per cubic yard. This is the quantity of water on which the water cement ratio is based, and does not include water absorbed by the aggregate

Ductility:

(english) Ductility generally refers to the amount of inelastic deformation which a material or structure experiences before complete failure. Quantitatively, ductility can be defined as the ratio of the total displacement or strain at failure, divided by the displacement or strain at the elastic limit.

Impermeable

(Concrete Engineering) The ability of a material or product to reduce or eliminate gaseous transmissions through it's mass; measured as the rate of Water Vapor Transmission (WVT). Note: Not all materials that are waterproof are vaporproof; all materials that are vaporproof are inherently waterproof.

Ottawa Sand

(Concrete Engineering) A sand used as a standard in testing hydraulic cements by means of mortar test specimens. Sand is produced by processing silica rock particles obtained by hydraulic mining of the orthoquartzite situated in open-pit deposits near Ottawa, Illinois; naturally rounded grains of nearly pure quartz.

Greenhouse gases

(Environmental Engineering) Gases which trap solar radiation. Of the solar energy entering the earth's atmosphere a portion is reflected back and a portion penetrates onto the earth's surface. The portion reflected back from the earth's surface is at a different wavelength that when it entered. Carbon dioxide and other gases, which pass solar radiation, absorb this reflected radiation, increasing the earth's temperature. This is much like a greenhouse, hence the name.

Abrasive 1

(english) Material for grinding, polishing, blasting, either in loose form or bonded to form wheels, bricks, or files, or applied to paper and cloth by glue or resin. Natural abrasives include emery, corundum, garnet, sand, flint, etc. Metallic shot and grit are also used as abrasives in cleaning castings

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด