ผลการค้นหา

ค้นเจอ 105 รายการ

Base Metal

(english) (1) The metal present in the largest proportion in an alloy; (2) the metal to be brazed, cut or welded; (3) after welding the part of the metal that was not melted during the process.

Blue Brittleness 2

(english) Reduced ductility occurring as a result of strain aging, when certain ferrous alloys are worked between 300 and 700 (degrees) F. This phenomenon may be observed at the working temperature or subsequently at lower temperatures.

Bloom 2

(english) A semi-finished hot rolled product, rectangular in cross section, produced on a blooming mill. For iron and steel, the width is not more than twice the thickness, and the cross-sectional area is usually not less than 36 sq. in. Iron and steel blooms are sometimes made by forging.

Autotrophic

(Environmental Engineering) Organisms which utilize inorganic carbon for synthesis of protoplasm. Ecologists narrow the definition further by requiring that autotrophs obtain their energy from the sun. In microbiologist parlance, this would be a photoautotroph. See photoautotrophic and chemoautotrophic.

Basic Oxygen Furnace (BOF)

(english) "WHAT A pear-shaped furnace, lined with refractory bricks, that refines molten iron from the blast furnace and scrap into steel. Up to 30% of the charge into the BOF can be scrap, with hot metal accounting for the rest. WHY BOFs, which can refine a heat (batch) of steel in less than 45 minutes, replaced open-hearth furnaces in the 1950s; the latter required five to six hours to process the metal. The BOF's rapid operation, lower cost and ease of control give it a distinct advantage over previous methods. HOW Scrap is dumped into the furnace vessel, followed by the hot metal from the blast furnace. A lance is lowered from above, through which blows a high-pressure stream of oxygen to cause chemical reactions that separate impurities as fumes or slag. Once refined, the liquid steel and slag are poured into separate containers. "

Aging 1

(english) A change in the properties of certain metal and alloys (such as steel) that occurs at ambient or moderately elevated temperatures after a hot working heat treatment or cold working operation. Typical properties impacted are hardness, yield strength, tensile strength, ductility, impact value, formability, magnetic properties, etc. See also Non-aging.

Statically determinate:

(english) A statically determinate structure is one where there is only one distribution of internal forces and reactions which satisfies equilibrium. In a statically determinate structure, internal forces and reactions can be determined by considering nothing more than equations of equilibrium.

Maximum Size Aggregate

(Concrete Engineering) Aggregate whose largest particle size is present in sufficient quantity to affect the physical properties of concrete; generally designated by the sieve size on which the maximum amount permitted to be retained is 5 or 10 percent by weight.

Equivalent

(Environmental Engineering) The mass of the compound which will produce one mole of available reacting substance. Thus, for an acid, this would be the mass of acid which will produce one mole of H+, for a base, one mole of OH-.

Backoff

Removal of part of coil from entry end of unit; may be necessitated by a defect in coil or by a wreck in the mill, etc. Backoff weight is the part of the coil that is removed and not finished/produced.

Blast Furnace 2

(english) A vertical shaft type smelting furnace in which an air blast is used, usually hot, for producing pih iron. The furnace is continuous in operation using iron ore, coke, and limestone as raw materials which are charged at the top while the molten iron and slag are collected at the bottom and are tapped out at intervals.

Ductility:

(english) Ductility generally refers to the amount of inelastic deformation which a material or structure experiences before complete failure. Quantitatively, ductility can be defined as the ratio of the total displacement or strain at failure, divided by the displacement or strain at the elastic limit.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด