ผลการค้นหา

have it* *have it *have it*
คำศัพท์ช่างภาษาอังกฤษ - ไทยคำศัพท์/สำนวน ทั้งหมดบทความ
ค้นเจอ 88 รายการ

คำศัพท์ช่างภาษาอังกฤษ - ไทยที่เกี่ยวข้องกับ "have it"

คลิกที่แต่ละคำเพื่อดูรายละเอียด

Pin support:

(english) In two dimensions, a pin support restrains two translation degrees of freedom but does not restrain rotation. When considering reaction forces, a pin support is usually considered to have two force components: one each about the x and y axes respectively.

Blow Back

(english) A coating defect consisting of a lower coating film weight on the bottom of the coated sheet caused by high velocity air in the oven. Blow back usually occurs with high solids coatings which have little solvent to evaporate and "set" the film.

Biochemical oxygen demand (BOD)

(Environmental Engineering) The amount of oxygen required to oxidize any organic matter present in a water during a specified period of time, usually 5 days. It is an indirect measure of the amount of organic matter present in a water.

Bright Dipping

(english) Chemical polishing of aluminum, often by treatment with a mixture of nitric acid and phosphoric acid, yielding a mirror-shiny (specular) highly reflective surface. It is almost always followed by anodizing to protect the surface and provide some choice of color.

Revibration

(Concrete Engineering) Delayed vibration of concrete that has already been placed and consolidated. Most effective when done at the latest time a running vibrator will sink of its own weight into the concrete and make it plastic and workable again.

Brasses

(english) Copper base alloys in which zinc is the principal alloying element. Brass is harder and mechanically stronger than either of its alloying elements copper or zinc. It is formable and ductile; develops high tensile strength with cold-working and is not heat treatable.

Modulus of elasticity:

(english) The proportional constant between stress and strain for material with linear elastic behavior: calculated as stress divided by strain. Modulus of elasticity can be interpreted as the slope of the stress-strain graph. It is usually denoted as E, sometimes known as Young's Modulus Y, or E-Modulus.

Backer (back-up plate)

(english) A “tool” or reinforcing part, which presses against the outer surface of an extrusion die, supporting it against the pressure of the extruding metal. The backer has an opening larger than the die aperture, allowing the extruded product to emerge without marring its soft surface.

Centroid:

(english) Similar to the concept of center of gravity, except that it applies to a two dimensional shape rather than an object. For a given shape, the centroid location corresponds to the center of gravity for a thin flat plate of that shape, made from a homogeneous material.

Elastic energy:

(english) The energy stored in deformed elastic material (e.g., a watch spring). Elastic energy equals where k is the stiffness, and is the associated deflection. Elastic energy is sometimes called elastic potential energy because it can be recovered when the object returns to its original shape; see potential energy.

Nitrification

(Environmental Engineering) The biological oxidation of ammonia and ammonium sequentially to nitrite and then nitrate. It occurs naturally in surface waters, and can be engineered in wastewater treatment systems. The purpose of nitrification in wastewater treatment systems is a reduction in the oxygen demand resulting from the ammonia.

Boil

(english) Agitation of a bath of metal caused by the liberation of a gas beneath its surface. May be deliberately induced by the addition of oxidizing material to a bath containing excess carbon. In the later case it is called a carbon boil and CO or CO2 are liberated.

 ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด