ผลการค้นหา

ค้นเจอ 29 รายการ

AAC - Autoclaved Aerated Concrete

(Concrete Engineering) Exceptionally lightweight precast concrete with high thermal qualities and fire resistence. Suitable for cutting with ordinary hand tools. Mix design is composed of portland cement, sand or siliceous material, lime, gypsum, finely powdered aluminum, and water. Initial mix is a combination of portland cement, sand, lime and gypsum to produce a slurry. Finely powdered aluminum mixed into a paste is added prior to placement into large, rail-like forms. The finely powdered aluminum reacts with the alkaline components of the cement and lime to produce hydrogen gas, which increases the volume approximately five times producing a uniformly, dispersed cellular structure. Units are cut to required shape. Units are placed in an autoclave, an enclosed pressurized chamber, and steam cured at 3500 F. Approximately 80% of the ultimate volume consists of air voids.

Agglomerating Processes

(english) "Fine particles of limestone (flux) and iron ore are difficult to handle and transport because of dusting and decomposition, so the powdery material usually is processed into larger pieces. The raw material's properties determine the technique that is used by mills. 1) SINTER Baked particles that stick together in roughly one-inch chunks. Normally used for iron ore dust collected from the blast furnaces. 2) PELLETS Iron ore or limestone particles are rolled into little balls in a balling drum and hardened by heat. 3) BRIQUETTES Small lumps are formed by pressing material together. Hot Iron Briquetting (HBI) is a concentrated iron ore substitute for scrap for use in electric furnaces.

Particle-Size Distribution

(Concrete Engineering) Particle distribution of granular materials among various sizes; for concrete material normally designated as gradation. Usually expressed in terms of cumulative percentages smaller or larger than each of a series of sieve openings or percentages between certain ranges of sieve openings.

Billet

(english) (1) A semi-finished section hot rolled from a metal ingot, with a rectangular cross section usually ranging from 16 to 36 in., the width being less than twice the thickness. Where the cross section exceeds 36 in., the term “bloom” is properly but not universally used. Sizes smaller than 16 in. are usually termed “bars”; a solid semi-finished round or square product which has been hot worked by forging, rolling, or extrusion. (2) A semi-finished, cogged, hot rolled or continuous-cast metal product of uniform section, usually rectangular with radiused corners. Billets are relatively larger than bars.

Boss

(english) A projection or an enlarged section of a casting through which a hole may be machine.

Flexibility:

(english) Flexibility is the inverse of stiffness. When a force is applied to a structure, there is a displacement in the direction of the force; flexibility is the ratio of the displacement divided by the force. High flexibility means that a small load produces a large displacement.

Balling Drum

(english) A rotating drum that is used for adding moisture to the sinter mix in the Blast Furnace. Also, it enhances a balling action where the smaller sized materials adhere to larger materials.

Entrapped Air

(Concrete Engineering) Air in concrete which is not purposely en-trained, Entrapped air bubbles are normally much larger and more irregular than entrained air bubbles.

Gillmore Needle

(Concrete Engineering) A device used in determining time of setting of hydraulic cement, described in ASTM 0 266. Gradation The sizing of granular materials; for concrete materials, usually expressed in terms of cumulative percentages larger or smaller than each of a series of sieve openings or the percentages between certain ranges of sieve openings.

Burnt Rubber

(english) Small or large black spots that generally show up on surface and are generally caused by pickling steel too hot.

Spall

(Concrete Engineering) A fragment, usually of flaky shape, detached from a larger mass by pressure, expansion from within the larger mass, a blow, or by the action of weather.

Bandsaw

(english) A power saw, the blade of which is a continuous,narrow,steel band having teeth on one edge and passing over two large pulley wheels.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด