ผลการค้นหา

ค้นเจอ 237 รายการ

Brown Sharp Gages

(english) A standard series of sizes refered to by numbers, in which the diameter of wire or thickness of sheet metal is generally produced and which is used in the manufacture of brass, bronze, copper, copper-base alloys and aluminum. These gage numbers have a definite relationship to each other. In this system, the decimal thickness is reduced by 50% every six gage numbers- while temper is expressed by the number of B&S gage numbers as cold reduced in thickness from previous annealing. For each B&S gage number in thickness reduction, where is assigned a hardness value of 1/4 hard.

Basket Screen

(english) A first stage in-line water filter for water delivered from the New Blowing Room Pump Room to the Blast Furnace. The strainer contains an electric-driven rotary sieve that catches particulates and prevents them from entering the water system.

Stiffness:

(english) This is a general term which may be applied to materials or structures. When a force is applied to a structure, there is a displacement in the direction of the force; stiffness is the ratio of the force divided by the displacement. High stiffness means that a large force produces a small displacement. When discussing the stiffness of a material, the concept is the same, except that stress substitutes for force, and strain substitutes for displacement; see modulus of elasticity.

Linear:

(english) A structure is said to behave linearly when its the deformation response is directly proportional to the loading (i.e. doubling the load doubles the displacement response). For a material, linear means that the stress is directly proportional to the strain.

Boron Steels

(english) The addition of boron in the range 0.0005-0.005% to certain steels increases the hardenability. A range of boron steels is now listed in the current BS 970 and are widely used for the production of cold headed fastenings.

Chlorofluorocarbons

(Environmental Engineering) Synthetic organic compounds used for refrigerants, aerosol propellants (prohibited in the U.S.), and blowing agents in plastic foams. CFCs migrate to the upper atmosphere destroying ozone and increasing global warming. Typical atmospheric residence times are 50 to 200 years.

Backwardation

(english) Market condition where the spot, or current price for a metal is higher than the three-month delivery price. This usually indicates immediate demand is perceived to be stronger than long-term demand. Not considered to be a "normal" market state (See Contango).

Particle-Size Distribution

(Concrete Engineering) Particle distribution of granular materials among various sizes; for concrete material normally designated as gradation. Usually expressed in terms of cumulative percentages smaller or larger than each of a series of sieve openings or percentages between certain ranges of sieve openings.

Hydrogenesis

(Concrete Engineering) Another term for condensation. The term is especially applied to base and soil substrates under highway pavements. where the barometric pump causes the inhalation of humid air, which then condenses in those structures, causing an ever increasing moisture content and sometimes instability.

Modulus of elasticity:

(english) The proportional constant between stress and strain for material with linear elastic behavior: calculated as stress divided by strain. Modulus of elasticity can be interpreted as the slope of the stress-strain graph. It is usually denoted as E, sometimes known as Young's Modulus Y, or E-Modulus.

Brazing

(english) Joining metals by fusion of nonferrous alloys that have melting points above 800 F (425C), but lower than those of the metals being joined. May be accomplished by a torch. Filler metal is ordinarily in rod form in torch brazing; whereas in furnace and dip brazing the work material is first assembled and the filler metal may then be applied as wire, washers, clips, bands, or may be bonded, as in brazing sheet.

Bloom 2

(english) A semi-finished hot rolled product, rectangular in cross section, produced on a blooming mill. For iron and steel, the width is not more than twice the thickness, and the cross-sectional area is usually not less than 36 sq. in. Iron and steel blooms are sometimes made by forging.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด