ผลการค้นหา

Have Down As* *Have Down As *Have Down As*

ค้นเจอ 151 รายการ

Back Rake

(english) The angular surface ground back from the cutting edge of cutting tools. On lathe cutting tools. The rake is positive if the face slopws down from the cutting edge toward the shank, and negative if the face sloopes upward toward the shank.

Blow Back

(english) A coating defect consisting of a lower coating film weight on the bottom of the coated sheet caused by high velocity air in the oven. Blow back usually occurs with high solids coatings which have little solvent to evaporate and "set" the film.

Unit Water Content

(Concrete Engineering) The quantity of water per unit volume of freshly mixed concrete, often expressed as gallons or pounds per cubic yard. This is the quantity of water on which the water cement ratio is based, and does not include water absorbed by the aggregate

Ductility:

(english) Ductility generally refers to the amount of inelastic deformation which a material or structure experiences before complete failure. Quantitatively, ductility can be defined as the ratio of the total displacement or strain at failure, divided by the displacement or strain at the elastic limit.

Impermeable

(Concrete Engineering) The ability of a material or product to reduce or eliminate gaseous transmissions through it's mass; measured as the rate of Water Vapor Transmission (WVT). Note: Not all materials that are waterproof are vaporproof; all materials that are vaporproof are inherently waterproof.

Ottawa Sand

(Concrete Engineering) A sand used as a standard in testing hydraulic cements by means of mortar test specimens. Sand is produced by processing silica rock particles obtained by hydraulic mining of the orthoquartzite situated in open-pit deposits near Ottawa, Illinois; naturally rounded grains of nearly pure quartz.

Abrasive 1

(english) Material for grinding, polishing, blasting, either in loose form or bonded to form wheels, bricks, or files, or applied to paper and cloth by glue or resin. Natural abrasives include emery, corundum, garnet, sand, flint, etc. Metallic shot and grit are also used as abrasives in cleaning castings

Brown Sharp Gages

(english) A standard series of sizes refered to by numbers, in which the diameter of wire or thickness of sheet metal is generally produced and which is used in the manufacture of brass, bronze, copper, copper-base alloys and aluminum. These gage numbers have a definite relationship to each other. In this system, the decimal thickness is reduced by 50% every six gage numbers- while temper is expressed by the number of B&S gage numbers as cold reduced in thickness from previous annealing. For each B&S gage number in thickness reduction, where is assigned a hardness value of 1/4 hard.

Component (of a vector):

(english) Any vector can be expressed as a collection of vectors whose sum is equal to the original vector. Each vector in this collection is a component of the original vector. It is common to express a vector in terms of components which are parallel to the x and y axes.

Aging 1

(english) A change in the properties of certain metal and alloys (such as steel) that occurs at ambient or moderately elevated temperatures after a hot working heat treatment or cold working operation. Typical properties impacted are hardness, yield strength, tensile strength, ductility, impact value, formability, magnetic properties, etc. See also Non-aging.

Slip Form

(Concrete Engineering) A form which is raised or pulled as concrete is placed; may move vertically to form wails, stacks, bins or silos, usually of uniform cross section from bottom to top; or a generally horizontal direction to lay concrete evenly for highways, on slopes and inverts of canals, tunnels, and siphons.

Blasting (Blast Cleaning)

(english) A process for cleaning or finishing metal objects by use of an air blast or centrifugal wheel that throws abrasive particles against the surface of the work pieces. Small, irregular particles of steel or iron are used as the abrasive in grit blasting, and steel or iron balls in shot blasting.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด