ผลการค้นหา

คำศัพท์ช่างภาษาอังกฤษ - ไทยคำศัพท์/สำนวน ทั้งหมดบทความ
ค้นเจอ 134 รายการ

คำศัพท์ช่างภาษาอังกฤษ - ไทยที่เกี่ยวข้องกับ "see out its term"

คลิกที่แต่ละคำเพื่อดูรายละเอียด

Revibration

(Concrete Engineering) Delayed vibration of concrete that has already been placed and consolidated. Most effective when done at the latest time a running vibrator will sink of its own weight into the concrete and make it plastic and workable again.

Autotrophic

(Environmental Engineering) Organisms which utilize inorganic carbon for synthesis of protoplasm. Ecologists narrow the definition further by requiring that autotrophs obtain their energy from the sun. In microbiologist parlance, this would be a photoautotroph. See photoautotrophic and chemoautotrophic.

Cement, Portland (ASTM C150) (Concrete Engineering)

A powdery substance made by burning, at a high temperature, a mixture of clay and limestone producing lumps called “clinkers” which are ground into a fine powder consisting of hydraulic calcium silicates. For non-portland cements, see aluminous cement.

Brasses

(english) Copper base alloys in which zinc is the principal alloying element. Brass is harder and mechanically stronger than either of its alloying elements copper or zinc. It is formable and ductile; develops high tensile strength with cold-working and is not heat treatable.

Breakout

(english) An accident caused by the failure of the walls of the hearth of the furnace resulting in liquid iron or slag (or both) flowing uncontrolled out of the blast furnace.

Backwardation

(english) Market condition where the spot, or current price for a metal is higher than the three-month delivery price. This usually indicates immediate demand is perceived to be stronger than long-term demand. Not considered to be a "normal" market state (See Contango).

Backer (back-up plate)

(english) A “tool” or reinforcing part, which presses against the outer surface of an extrusion die, supporting it against the pressure of the extruding metal. The backer has an opening larger than the die aperture, allowing the extruded product to emerge without marring its soft surface.

NPDES

(Environmental Engineering) The National Pollutant Discharge Elimination System. The discharge criteria and permitting system established by the U.S. EPA as a result of the Clean Water Act and its subsequent amendments or the permit required by each discharger as a result of the Clean Water Act.

Bridling

(english) The cold working of dead soft annealed strip metal immediately prior to a forming, bending, or drawing operation. A process designed to prevent the formulation of Luder's lines. Caution-Bridled metal should be used promptly and not permitted to (of itself) return to its pre-bridled condition.

Boil

(english) Agitation of a bath of metal caused by the liberation of a gas beneath its surface. May be deliberately induced by the addition of oxidizing material to a bath containing excess carbon. In the later case it is called a carbon boil and CO or CO2 are liberated.

Aging 1

(english) A change in the properties of certain metal and alloys (such as steel) that occurs at ambient or moderately elevated temperatures after a hot working heat treatment or cold working operation. Typical properties impacted are hardness, yield strength, tensile strength, ductility, impact value, formability, magnetic properties, etc. See also Non-aging.

Burr

(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.

 ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด