ผลการค้นหา

Bars

แปลว่า(english) A relatively long straight, rigid piece pf metal; long steel products rolled from billets into such shapes as squares,rectangles, rounds,angles,channels,hexagons,and tees. In steel, “merchant bars” include rounds,flats,angles,squares,and channels that are used by fabricators to manufacture a wide variety of products such as furniture,stair railings and farm equipment. Concrete reinforcing bar (rebar) is used to strengthen concrete in highways,bridges and buildings.

Blue Annealing

แปลว่า(english) Heating hot rolled ferrous sheet in an open furnace to a temperature within the transformation range and then cooling in air, in order to soften the metal. The formation of a bluish oxide on the surface is incidental.

Acid Process 1

แปลว่า(english) A process of making steel, either Bessemer, open-hearth or electric, in which the furnace is lined with a siliceous refractory and for which low phosphorus pig iron is required as this element is not removed.

Bending Angle

แปลว่า(english) A 'V-shaped' piece of angle iron attached to the rear of the coil car in the Strip Steel, which is used to help the operator put bends into the front end of a coil.

Corrosive waste

แปลว่า(Environmental Engineering) A waste that is outside the pH range of 2 to 12.5 or a waste that corrodes steel at a rate greater than 6.35 mm (0.25 in) per year. One of EPA's four hazardous waste properties.

Acid-Process

แปลว่า(english) A process of making steel, either Bessemer, open-hearth or electric, in which the furnace is lined with a siliceous refractory and for which low phosphorus pig iron is required as this element is not removed.

Bottle Top Mold

แปลว่า(english) Ingot mold, with the top constricted; used in the manufacture of capped steel, the metal in the constriction being covered with a cap fitting into the bottle-neck, which stops rimming action by trapping escaping gases.

Yield stress:

แปลว่า(english) A material loaded beyond its yield stress, no longer exhibits linear elastic behavior. Metals, particularly mild steel, generally have a very well defined yield stress compared to other materials. Yield stress is sometimes called yield strength.

Blow Back

แปลว่า(english) A coating defect consisting of a lower coating film weight on the bottom of the coated sheet caused by high velocity air in the oven. Blow back usually occurs with high solids coatings which have little solvent to evaporate and "set" the film.

Brinell Hardness

แปลว่า(english) The hardness of a metal or part, as represented by the number obtained from the ratio between the load applied on the spherical area of the impression made by a steel ball forced into the surface of the material tested.

Blue Brittleness

แปลว่า(english) Brittleness exhibited by some steels after being heated to some temperature within the range of 300 (degrees) to 650 (degrees) F, and more especially if the steel is worked at the elevated temperature. Killed steels are virtually free of this kind of brittleness.

Basic Oxygen Furnace (BOF)

แปลว่า(english) "WHAT A pear-shaped furnace, lined with refractory bricks, that refines molten iron from the blast furnace and scrap into steel. Up to 30% of the charge into the BOF can be scrap, with hot metal accounting for the rest. WHY BOFs, which can refine a heat (batch) of steel in less than 45 minutes, replaced open-hearth furnaces in the 1950s; the latter required five to six hours to process the metal. The BOF's rapid operation, lower cost and ease of control give it a distinct advantage over previous methods. HOW Scrap is dumped into the furnace vessel, followed by the hot metal from the blast furnace. A lance is lowered from above, through which blows a high-pressure stream of oxygen to cause chemical reactions that separate impurities as fumes or slag. Once refined, the liquid steel and slag are poured into separate containers. "