ผลการค้นหา

ค้นเจอ 119 รายการ

Component (of a vector):

(english) Any vector can be expressed as a collection of vectors whose sum is equal to the original vector. Each vector in this collection is a component of the original vector. It is common to express a vector in terms of components which are parallel to the x and y axes.

Aging 1

(english) A change in the properties of certain metal and alloys (such as steel) that occurs at ambient or moderately elevated temperatures after a hot working heat treatment or cold working operation. Typical properties impacted are hardness, yield strength, tensile strength, ductility, impact value, formability, magnetic properties, etc. See also Non-aging.

Slip Form

(Concrete Engineering) A form which is raised or pulled as concrete is placed; may move vertically to form wails, stacks, bins or silos, usually of uniform cross section from bottom to top; or a generally horizontal direction to lay concrete evenly for highways, on slopes and inverts of canals, tunnels, and siphons.

Blasting (Blast Cleaning)

(english) A process for cleaning or finishing metal objects by use of an air blast or centrifugal wheel that throws abrasive particles against the surface of the work pieces. Small, irregular particles of steel or iron are used as the abrasive in grit blasting, and steel or iron balls in shot blasting.

Gravity:

(english) An attractive force between two objects; each object accelerates at a rate equal to the attractive force divided by the object's mass. Objects near the surface of the earth tend to accelerate toward the earth's center at a rate of ; this value is often called the gravitational constant and denoted as g.

Normal strain:

(english) Strain measuring the intensity of deformation along an axis. Normal strain is usually denoted by . Average normal strain between two points is calculated as (Delta L / L), where L is the original distance between the points, and L is the change in that distance. Normal strain is often simply called strain.

Pozzolan (ASTM C 618)

(Concrete Engineering) A siliceous, or siliceous and aluminous material, which in itself possesses little or no cementitious value but will, in a finely divided form, such as a powder or liquid and in the presence of moisture, chemically react with calcium hydroxide at ordinary temperatures to form permanent, insoluble compounds possessing cementitious properties.

Pumping (of Pavements)

(Concrete Engineering) The ejection of a mixture of water and solid materials such as clay or silt along cracks, transverse or longitudinal joints, and along pavement edges caused by downward slab movement due to the passage of heavy loads, machinery or equipment over the pavement after free water has accumulated in or on the subbase, subgrade or basecourse.

Water-Cement Ratio

(Concrete Engineering) The ratio of the amount of water, exclusive of that absorbed by the aggregates, to the amount of cement in a concrete mix. Typically expressed as percentage of water, by weight in pounds, to the total weight of portland cement, fly ash, and any other cementitious material, per cubic yard, exclusive of any aggregates.

Blast Furnace 2

(english) A vertical shaft type smelting furnace in which an air blast is used, usually hot, for producing pih iron. The furnace is continuous in operation using iron ore, coke, and limestone as raw materials which are charged at the top while the molten iron and slag are collected at the bottom and are tapped out at intervals.

Inertial Force:

(english) A fictitious force used for convenience in visualizing the effects of forces on bodies in motion. For an accelerating body, the inertial force is considered as a body force whose resultant acts at the object's center of gravity in a direction opposite the acceleration. The magnitude of the force is the mass of the object times the magnitude of the acceleration.

Stiffness:

(english) This is a general term which may be applied to materials or structures. When a force is applied to a structure, there is a displacement in the direction of the force; stiffness is the ratio of the force divided by the displacement. High stiffness means that a large force produces a small displacement. When discussing the stiffness of a material, the concept is the same, except that stress substitutes for force, and strain substitutes for displacement; see modulus of elasticity.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด