ผลการค้นหา

Cell

แปลว่า(Environmental Engineering) A unit of varying dimensions in a landfill which is isolated from the environment by 6 to 12 inches of soil cover. A cell is one day's waste or less. A cell is covered with soil at the end of each day.

Modulus of elasticity:

แปลว่า(english) The proportional constant between stress and strain for material with linear elastic behavior: calculated as stress divided by strain. Modulus of elasticity can be interpreted as the slope of the stress-strain graph. It is usually denoted as E, sometimes known as Young's Modulus Y, or E-Modulus.

Billet

แปลว่า(english) (1) A semi-finished section hot rolled from a metal ingot, with a rectangular cross section usually ranging from 16 to 36 in., the width being less than twice the thickness. Where the cross section exceeds 36 in., the term “bloom” is properly but not universally used. Sizes smaller than 16 in. are usually termed “bars”; a solid semi-finished round or square product which has been hot worked by forging, rolling, or extrusion. (2) A semi-finished, cogged, hot rolled or continuous-cast metal product of uniform section, usually rectangular with radiused corners. Billets are relatively larger than bars.

Bend Test

แปลว่า(english) Various tests which is used to ascertain the toughness and ductility of a metal product, in which the material is bent around its axis and/ or around an outside radius. A complete test might specify such a bend to be both with and against the direction of grain. For testing, samples should be edge filed to remove burrs and any edgewise cracks resulting from slitting or shearing. If a vice is to be employed, then you must line the jaws with some soft metal, to permit a flow of the metal in the piece being tested.

Beryllium Copper

แปลว่า(english) An alloy of copper and 2-3% beryllium with optionally fractional percentages of nickel or cobalt. Alloys of this series show remarkable age-hardening properties and an ultimate hardness of about 400 Brinell (Rockwell C43). Because of such hardness and good electrical conductivity, beryllium-copper is used in electrical switches, springs, etc.

Bismuth

แปลว่า(english) Chemical symbol Bi. A soft, course cystalline heavy metal with a silvery white color and pinkish tinge; usually produced as a by-product of copper,leaad and other metals. Has a thermal conductivity lower than all other metals except mercury. Used as alloying agent but leading use is in pharmaceuticals.

Pozzolan (ASTM C 618)

แปลว่า(Concrete Engineering) A siliceous, or siliceous and aluminous material, which in itself possesses little or no cementitious value but will, in a finely divided form, such as a powder or liquid and in the presence of moisture, chemically react with calcium hydroxide at ordinary temperatures to form permanent, insoluble compounds possessing cementitious properties.

Blast Furnace

แปลว่า(english) 1) A furnace in which solid fuel (limestone, coke, iron ore) is combined with high-pressure, hot air blast (120,000 psi) to smelt ore in a continuous process (They are never stopped. They can be slowed down or idled). A Blast Furnace in the iron and steel industry is used to produce liquid iron.

Burr

แปลว่า(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.

Break Test (for tempered steel)

แปลว่า(english) A method of testing hardened and tempered high carbon spring steel strip wherein the specimen is held and bent across the grain in a vice-like calibrated testing machine. Pressure is applied until the metal fractures at which point a reading is taken and compared with a standard chart of brake limitations for various thickness ranges.

Moment of inertia (I):

แปลว่า(english) Moment of inertia has two distinct but related meanings: 1) it is a property of a an object relating to the magnitude of the moment required to rotate the object and overcome its inertia. 2) A property of a two dimensional cross section shape with respect to an axis, usually an axis through the centroid of the shape.

Construction Joint

แปลว่า(Concrete Engineering) The contact between the placed concrete and concrete surfaces, against or upon which concrete is to be placed and to which new concrete is to adhere, that has become so rigid that the new concrete cannot be incorporated integrally by vibration with that previously placed. Unformed construction joints are horizontally placed or nearly so.