ผลการค้นหา

hard work* *hard work *hard work*
คำศัพท์ช่างภาษาอังกฤษ - ไทยคำศัพท์/สำนวน ทั้งหมดบทความ
ค้นเจอ 92 รายการ

คำศัพท์ช่างภาษาอังกฤษ - ไทยที่เกี่ยวข้องกับ "hard work"

คลิกที่แต่ละคำเพื่อดูรายละเอียด

Agile development (also referred to as agile process model)

(Software Engineering) an adapted version of software engineering that emphasizes customer communication, incremental software delivery, informal methods and work products, and highly motivated teams.

Z-Mill

(english) The full name for z-mill is Sendzimir mill. A Z-mill operates with a very small diameter work roll, normally about 2 inches, backed up by a number of rolls in a pyramid-shaped stack. This roll set up allows you to exert extremely high forces through the work roll and yet keep the work roll from extreme flexing. The take-up roll on the Z-Mill also exerts a tension on the coil as it comes through the mill. The combination of high pressure and tension makes the mill capable of rolling material thin and flat.

Stucco

(Concrete Engineering) A portland cement mortar material that can be applied to the surface of any building or structure to form a hard and durable covering for the exterior wails or other exterior surfaces.

Rocaille, Rococo

คำฝรั่งเศสหมายถึง rock work เป็นศิลปที่นิยมกันในราชสำนักพระเจ้าหลุยส์ที่ 15 (1700-1790) เป็นงานตกแต่งที่ละเอียดละออ วิจิตรพิสดาร มีลักษณะพริ้วไหวอ่อนช้อย มีรากฐานจากธรรมชาติ เช่น ลายเปลือกหอย ใบไม้ ดอกไม้ โค้งรูปตัว C ฯลฯ

Burning

(english) (1) Permanently damaging a metal or alloy by heating to cause either incipient melting or intergranular oxidation. (2) In grinding getting the work hot enough to cause discoloration or to change the microstructure by tempering or hardening.

Blasting (Blast Cleaning)

(english) A process for cleaning or finishing metal objects by use of an air blast or centrifugal wheel that throws abrasive particles against the surface of the work pieces. Small, irregular particles of steel or iron are used as the abrasive in grit blasting, and steel or iron balls in shot blasting.

Brazing

(english) Joining metals by fusion of nonferrous alloys that have melting points above 800 F (425C), but lower than those of the metals being joined. May be accomplished by a torch. Filler metal is ordinarily in rod form in torch brazing; whereas in furnace and dip brazing the work material is first assembled and the filler metal may then be applied as wire, washers, clips, bands, or may be bonded, as in brazing sheet.

Brown Sharp Gages

(english) A standard series of sizes refered to by numbers, in which the diameter of wire or thickness of sheet metal is generally produced and which is used in the manufacture of brass, bronze, copper, copper-base alloys and aluminum. These gage numbers have a definite relationship to each other. In this system, the decimal thickness is reduced by 50% every six gage numbers- while temper is expressed by the number of B&S gage numbers as cold reduced in thickness from previous annealing. For each B&S gage number in thickness reduction, where is assigned a hardness value of 1/4 hard.

 ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด