ผลการค้นหา

Calcium Aluminate Cement

แปลว่า(Concrete Engineering) The product obtained by pulverizing clinker consisting essentially of hydraulic calcium aluminates resulting from fusing or sintering a suitable proportioned mixture of aluminous and calcareous materials.

By Coil

แปลว่า(english) Selling term which refers to product sold in the form of a coil vs. cut plate. "Bi Coil" is also used in production to refer to coils vs. cut plate

Bright Drawing

แปลว่า(english) The process of drawing hot rolled steel through a die to impart close dimensional tolerances, a bright scale free surface and improved mechanical properties. The product is termed bright steel.

Factoring

แปลว่า(Software Engineering) a technique that distributes control and work in a top-down manner within a software architecture (used a part of structured analysis)

Agile development (also referred to as agile process model)

แปลว่า(Software Engineering) an adapted version of software engineering that emphasizes customer communication, incremental software delivery, informal methods and work products, and highly motivated teams.

Z-Mill

แปลว่า(english) The full name for z-mill is Sendzimir mill. A Z-mill operates with a very small diameter work roll, normally about 2 inches, backed up by a number of rolls in a pyramid-shaped stack. This roll set up allows you to exert extremely high forces through the work roll and yet keep the work roll from extreme flexing. The take-up roll on the Z-Mill also exerts a tension on the coil as it comes through the mill. The combination of high pressure and tension makes the mill capable of rolling material thin and flat.

Bearing Strength

แปลว่า(english) The maximum bearing load at failure divided by the effective bearing area. In a pinned or riveted joint, the iffective area is calculated as the product of the diameter of the hole and the thickness of the bearing member.

Impermeable

แปลว่า(Concrete Engineering) The ability of a material or product to reduce or eliminate gaseous transmissions through it's mass; measured as the rate of Water Vapor Transmission (WVT). Note: Not all materials that are waterproof are vaporproof; all materials that are vaporproof are inherently waterproof.

Energy:

แปลว่า(english) A property of a body related to its ability to move a force through a distance opposite the force's direction; energy is the product of the magnitude of the force times the distance. Energy may take several forms: see kinetic energy, potential energy, and elastic energy.

Backer (back-up plate)

แปลว่า(english) A “tool” or reinforcing part, which presses against the outer surface of an extrusion die, supporting it against the pressure of the extruding metal. The backer has an opening larger than the die aperture, allowing the extruded product to emerge without marring its soft surface.

Rocaille, Rococo

แปลว่าคำฝรั่งเศสหมายถึง rock work เป็นศิลปที่นิยมกันในราชสำนักพระเจ้าหลุยส์ที่ 15 (1700-1790) เป็นงานตกแต่งที่ละเอียดละออ วิจิตรพิสดาร มีลักษณะพริ้วไหวอ่อนช้อย มีรากฐานจากธรรมชาติ เช่น ลายเปลือกหอย ใบไม้ ดอกไม้ โค้งรูปตัว C ฯลฯ

Billet

แปลว่า(english) (1) A semi-finished section hot rolled from a metal ingot, with a rectangular cross section usually ranging from 16 to 36 in., the width being less than twice the thickness. Where the cross section exceeds 36 in., the term “bloom” is properly but not universally used. Sizes smaller than 16 in. are usually termed “bars”; a solid semi-finished round or square product which has been hot worked by forging, rolling, or extrusion. (2) A semi-finished, cogged, hot rolled or continuous-cast metal product of uniform section, usually rectangular with radiused corners. Billets are relatively larger than bars.