ผลการค้นหา

charge at* *charge at *charge at*
คำศัพท์ช่างภาษาอังกฤษ - ไทยคำศัพท์/สำนวน ทั้งหมดบทความ
ค้นเจอ 102 รายการ

คำศัพท์ช่างภาษาอังกฤษ - ไทยที่เกี่ยวข้องกับ "charge at"

คลิกที่แต่ละคำเพื่อดูรายละเอียด

Pin connection:

(english) In two dimensions, a pin connection restrains two translation degrees of freedom but does not restrain rotation. Since the rotation degree of freedom is unrestrained at a pin connection, it transfers no moment.

Box Annealing 2

(english) A process of annealing a ferrous alloy in a closed metal container, with or without packing materials, in order to minimize the effects of oxidation. The charge is normally heated slowly to a temperature below the transformation range, but occasionally above or within it, and then is slowly cooled.

Blast Cleaning (blasting)

(english) A process for cleaning or finishing metal objects by use of an air jet or centrifugal wheel that propels abrasive particles (grit, sand, or shot) against the surfaces of the workpiece at high velocity.

Structural model:

(english) An idealization for analysis purposes of a real or conceived structure. A structural model includes boundaries limiting the scope of the analysis. Supports occur at these boundaries, representing things which hold the structure in place.

Box Annealing

(english) Annealing a metal or alloy in a sealed container under conditions that minimize oxidation. In box annealing a ferrous alloy, the charge is usually heated slowly to a temperature below the transformation range, but sometimes above or within it, and is then cooled slowly; this process is also called close annealing or pot annealing.

Cement, Portland (ASTM C150) (Concrete Engineering)

A powdery substance made by burning, at a high temperature, a mixture of clay and limestone producing lumps called “clinkers” which are ground into a fine powder consisting of hydraulic calcium silicates. For non-portland cements, see aluminous cement.

Corrosive waste

(Environmental Engineering) A waste that is outside the pH range of 2 to 12.5 or a waste that corrodes steel at a rate greater than 6.35 mm (0.25 in) per year. One of EPA's four hazardous waste properties.

Revibration

(Concrete Engineering) Delayed vibration of concrete that has already been placed and consolidated. Most effective when done at the latest time a running vibrator will sink of its own weight into the concrete and make it plastic and workable again.

Bearing Strength

(english) The maximum bearing load at failure divided by the effective bearing area. In a pinned or riveted joint, the iffective area is calculated as the product of the diameter of the hole and the thickness of the bearing member.

Cell

(Environmental Engineering) A unit of varying dimensions in a landfill which is isolated from the environment by 6 to 12 inches of soil cover. A cell is one day's waste or less. A cell is covered with soil at the end of each day.

Blue Brittleness

(english) Brittleness exhibited by some steels after being heated to some temperature within the range of 300 (degrees) to 650 (degrees) F, and more especially if the steel is worked at the elevated temperature. Killed steels are virtually free of this kind of brittleness.

Mixing Speed

(Concrete Engineering) Rate of mixer drum rotation or that of the paddles in a pan, open-top, or trough type mixer, when mixing a batch; expressed in revolutions per minute (rpm) or in peripheral] feet per minute of A point on the circumference at maximum diameter.

 ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด