ผลการค้นหา

ค้นเจอ 94 รายการ

Statically equivalent:

(english) Two force systems are statically equivalent when their resultants are equal. Physically, this means that the force systems tend to impart the same motion when applied to an object; note that the distribution of resulting internal forces in the object may be different.

Brinell Hardness Test

(english) A common standard method of measuring the hardness of materials. The smooth surface of the metal is subjected to indentation by a hardened steel ball under pressure. The diameter of the indentation, in the material surface, is then measured by a microscope and the hardness value is read from a chart or determined by a prescribed formula.

Modulus of elasticity:

(english) The proportional constant between stress and strain for material with linear elastic behavior: calculated as stress divided by strain. Modulus of elasticity can be interpreted as the slope of the stress-strain graph. It is usually denoted as E, sometimes known as Young's Modulus Y, or E-Modulus.

Bridling

(english) The cold working of dead soft annealed strip metal immediately prior to a forming, bending, or drawing operation. A process designed to prevent the formulation of Luder's lines. Caution-Bridled metal should be used promptly and not permitted to (of itself) return to its pre-bridled condition.

Elastic energy:

(english) The energy stored in deformed elastic material (e.g., a watch spring). Elastic energy equals where k is the stiffness, and is the associated deflection. Elastic energy is sometimes called elastic potential energy because it can be recovered when the object returns to its original shape; see potential energy.

Nitrification

(Environmental Engineering) The biological oxidation of ammonia and ammonium sequentially to nitrite and then nitrate. It occurs naturally in surface waters, and can be engineered in wastewater treatment systems. The purpose of nitrification in wastewater treatment systems is a reduction in the oxygen demand resulting from the ammonia.

Boil

(english) Agitation of a bath of metal caused by the liberation of a gas beneath its surface. May be deliberately induced by the addition of oxidizing material to a bath containing excess carbon. In the later case it is called a carbon boil and CO or CO2 are liberated.

Component (of a vector):

(english) Any vector can be expressed as a collection of vectors whose sum is equal to the original vector. Each vector in this collection is a component of the original vector. It is common to express a vector in terms of components which are parallel to the x and y axes.

Reactive waste

(Environmental Engineering) A waste which; 1) reacts violently with water, 2) forms potentially explosive mixtures with water, 3) is normally unstable, 4) contains cyanide or sulfide in sufficient quantity to evolve toxic fumes at high or low pH, 5) is capable of exploding if heated under pressure, or 6) is an explosive compound listed in Department of Transportation (DoT) regulations. One of EPA's four hazardous waste properties.

Moist Room

(Concrete Engineering) A room used for storing and curing cementitious test specimens. The atmosphere of this room is maintained at a temperature of 73.4 3.0'F or 23.0*1.7'0 and relative humidity of at least 98 percent. These facilities must be adequate to continually maintain free moisture on the exteriors of test specimens.

Blast Furnace

(english) 1) A furnace in which solid fuel (limestone, coke, iron ore) is combined with high-pressure, hot air blast (120,000 psi) to smelt ore in a continuous process (They are never stopped. They can be slowed down or idled). A Blast Furnace in the iron and steel industry is used to produce liquid iron.

Billet 2

(english) A solid semi-finished round or square product that has been hot worked by forging, rolling, or extrusion. An iron or steel billet has a minimum width or thickness of 1 1/2 in. and the cross-sectional area varies from 2 1/4 to 36 sq. in. For nonferrous metals, it may also be a casting suitable for finished or semi-finished rolling or for extrusion.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด