ผลการค้นหา

Burr

แปลว่า(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.

Broaching

แปลว่า(english) Smoothing machined holes or outside surfaces of castings by drawing pushing on or more broaches (special cutting tools) through the roughed out hole.

Broach

แปลว่า(english) A long, tapered cutting tool with serrations which,when forced through a hole or across a surface, cuts a desired shape or size.

Bell Mouth

แปลว่า(english) The flaring or tapering of a machined hole, usually made at the entrance end because of misalignment or spring of the cutting tool.

Bevel

แปลว่า(english) Angle formed between the prepared edge of the end of tube and a plane perpendicular to the surface. Standard pipe bevel is 30 degrees.

Bandsaw

แปลว่า(english) A power saw, the blade of which is a continuous,narrow,steel band having teeth on one edge and passing over two large pulley wheels.

Normal stress:

แปลว่า(english) Stress acting perpendicular to an imaginary plane cutting through an object. Normal stress has two senses: compression and tension. Normal stress is often simply called stress.

Burn

แปลว่า(english) 1) Process of cutting metal by a stream of fuel and oxygen, 2) to permanently damage a metal or alloy by heating to cause either incipient melting or intergranular oxidation.

Section Modulus:

แปลว่า(english) A property of a cross sectional shape, which depends on shape, and orientation. Section modulus is usually denoted S, and S = I/c, where I = moment of inertia about an axis through the centroid, and c is the distance from the centroid to the extreme edge of the section.

Bend Test

แปลว่า(english) Various tests which is used to ascertain the toughness and ductility of a metal product, in which the material is bent around its axis and/ or around an outside radius. A complete test might specify such a bend to be both with and against the direction of grain. For testing, samples should be edge filed to remove burrs and any edgewise cracks resulting from slitting or shearing. If a vice is to be employed, then you must line the jaws with some soft metal, to permit a flow of the metal in the piece being tested.

AAC - Autoclaved Aerated Concrete

แปลว่า(Concrete Engineering) Exceptionally lightweight precast concrete with high thermal qualities and fire resistence. Suitable for cutting with ordinary hand tools. Mix design is composed of portland cement, sand or siliceous material, lime, gypsum, finely powdered aluminum, and water. Initial mix is a combination of portland cement, sand, lime and gypsum to produce a slurry. Finely powdered aluminum mixed into a paste is added prior to placement into large, rail-like forms. The finely powdered aluminum reacts with the alkaline components of the cement and lime to produce hydrogen gas, which increases the volume approximately five times producing a uniformly, dispersed cellular structure. Units are cut to required shape. Units are placed in an autoclave, an enclosed pressurized chamber, and steam cured at 3500 F. Approximately 80% of the ultimate volume consists of air voids.

Bent Axis Pumps

แปลว่า(english) In this pump, the pistons are at an angle to the drive shaft and Thrust Plate. The piston block shaft is connected to the drive shaft by a universal joint, not shown. The drive shaft, thrust plate, piston block shaft, and piston block all revolve. The connecting rods are attached to the thrust plate and revolve with it, unlike the swash plate pump where the piston rods slide past a stationary swash plate. The outlet ports are semi-circular holes in the Valve Plate, shown on the far right of the animation on edge and in a head-on view below, right. As the pump revolves, half the pistons suck in fluid as they pass over the intake port. The other pistons discharge their fluid through the outlet port. This pump should be compared to the radial piston pump, swash plate pump, and wobble pump.