ผลการค้นหา

BETA RATIO (#)

แปลว่า(english) The amount, expressed as a ratio, of particles in a fluid stream upstream of a filter, after the fluid posses through a filter, divided by the amount of particles downstream, for a particular size particle.

Saponification

แปลว่า(Concrete Engineering) The deposit of a gray scum or gray dust on the inside surface of a subgrade wall or floor; as the result of moisture moving through the concrete and washing certain chemicals from the concrete mass.

Impermeable

แปลว่า(Concrete Engineering) The ability of a material or product to reduce or eliminate gaseous transmissions through it's mass; measured as the rate of Water Vapor Transmission (WVT). Note: Not all materials that are waterproof are vaporproof; all materials that are vaporproof are inherently waterproof.

Z-Mill

แปลว่า(english) The full name for z-mill is Sendzimir mill. A Z-mill operates with a very small diameter work roll, normally about 2 inches, backed up by a number of rolls in a pyramid-shaped stack. This roll set up allows you to exert extremely high forces through the work roll and yet keep the work roll from extreme flexing. The take-up roll on the Z-Mill also exerts a tension on the coil as it comes through the mill. The combination of high pressure and tension makes the mill capable of rolling material thin and flat.

Energy:

แปลว่า(english) A property of a body related to its ability to move a force through a distance opposite the force's direction; energy is the product of the magnitude of the force times the distance. Energy may take several forms: see kinetic energy, potential energy, and elastic energy.

Section Modulus:

แปลว่า(english) A property of a cross sectional shape, which depends on shape, and orientation. Section modulus is usually denoted S, and S = I/c, where I = moment of inertia about an axis through the centroid, and c is the distance from the centroid to the extreme edge of the section.

Moment of inertia (I):

แปลว่า(english) Moment of inertia has two distinct but related meanings: 1) it is a property of a an object relating to the magnitude of the moment required to rotate the object and overcome its inertia. 2) A property of a two dimensional cross section shape with respect to an axis, usually an axis through the centroid of the shape.

Basic Oxygen Furnace (BOF)

แปลว่า(english) "WHAT A pear-shaped furnace, lined with refractory bricks, that refines molten iron from the blast furnace and scrap into steel. Up to 30% of the charge into the BOF can be scrap, with hot metal accounting for the rest. WHY BOFs, which can refine a heat (batch) of steel in less than 45 minutes, replaced open-hearth furnaces in the 1950s; the latter required five to six hours to process the metal. The BOF's rapid operation, lower cost and ease of control give it a distinct advantage over previous methods. HOW Scrap is dumped into the furnace vessel, followed by the hot metal from the blast furnace. A lance is lowered from above, through which blows a high-pressure stream of oxygen to cause chemical reactions that separate impurities as fumes or slag. Once refined, the liquid steel and slag are poured into separate containers. "

Bent Axis Pumps

แปลว่า(english) In this pump, the pistons are at an angle to the drive shaft and Thrust Plate. The piston block shaft is connected to the drive shaft by a universal joint, not shown. The drive shaft, thrust plate, piston block shaft, and piston block all revolve. The connecting rods are attached to the thrust plate and revolve with it, unlike the swash plate pump where the piston rods slide past a stationary swash plate. The outlet ports are semi-circular holes in the Valve Plate, shown on the far right of the animation on edge and in a head-on view below, right. As the pump revolves, half the pistons suck in fluid as they pass over the intake port. The other pistons discharge their fluid through the outlet port. This pump should be compared to the radial piston pump, swash plate pump, and wobble pump.