ผลการค้นหา

ค้นเจอ 221 รายการ

Burr

(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.

Pumping (of Pavements)

(Concrete Engineering) The ejection of a mixture of water and solid materials such as clay or silt along cracks, transverse or longitudinal joints, and along pavement edges caused by downward slab movement due to the passage of heavy loads, machinery or equipment over the pavement after free water has accumulated in or on the subbase, subgrade or basecourse.

A Sheet Metal Screw

(english) Sheet metal screws with (a) sharp-pointed ends; and (b) fewer threads per inch than type AB screws; and (c) deeper threads with bettere gripping power than type AB. The industrial Fasteners Institue incorrectly labes type A an “obsolete” thread though it is universally preferred in 18-8 stainless over type AB, especially by the marine industry.

Blister

(english) 1) Coating defect consisting of the formation of bubbles in a coating, which appear as hemispherical elevations. The blisters are hollow, and are usually caused by entrapped air or solvent. 2) A raised spot on the surface on the surface of metal due to expansion of gas which causes a subsurface metal separation such as inclusions and small laminations.

Strength:

(english) A very general term that may be applied to a material or a structure. In a material, strength refers to a level of stress at which there is a significant change in the state of the material, e.g., yielding or rupture. In a structure, strength refers to a level of level of loading which produces a significant change in the state of the structure, e.g., inelastic deformations, buckling, or collapse.

Support:

(english) A support contributes to keeping a structure in place by restraining one or more degrees of freedom. In a structural model, supports represent boundary entities which are not included in the model itself, e.g., foundations, abutments, or the earth itself. For each restrained translation degree of freedom at a support, there is a corresponding reaction force; for each restrained rotation degree of freedom, there is a reaction moment.

Basic Oxygen Furnace (BOF)

(english) "WHAT A pear-shaped furnace, lined with refractory bricks, that refines molten iron from the blast furnace and scrap into steel. Up to 30% of the charge into the BOF can be scrap, with hot metal accounting for the rest. WHY BOFs, which can refine a heat (batch) of steel in less than 45 minutes, replaced open-hearth furnaces in the 1950s; the latter required five to six hours to process the metal. The BOF's rapid operation, lower cost and ease of control give it a distinct advantage over previous methods. HOW Scrap is dumped into the furnace vessel, followed by the hot metal from the blast furnace. A lance is lowered from above, through which blows a high-pressure stream of oxygen to cause chemical reactions that separate impurities as fumes or slag. Once refined, the liquid steel and slag are poured into separate containers. "

Bent Axis Pumps

(english) In this pump, the pistons are at an angle to the drive shaft and Thrust Plate. The piston block shaft is connected to the drive shaft by a universal joint, not shown. The drive shaft, thrust plate, piston block shaft, and piston block all revolve. The connecting rods are attached to the thrust plate and revolve with it, unlike the swash plate pump where the piston rods slide past a stationary swash plate. The outlet ports are semi-circular holes in the Valve Plate, shown on the far right of the animation on edge and in a head-on view below, right. As the pump revolves, half the pistons suck in fluid as they pass over the intake port. The other pistons discharge their fluid through the outlet port. This pump should be compared to the radial piston pump, swash plate pump, and wobble pump.

Bars

(english) A relatively long straight, rigid piece pf metal; long steel products rolled from billets into such shapes as squares,rectangles, rounds,angles,channels,hexagons,and tees. In steel, “merchant bars” include rounds,flats,angles,squares,and channels that are used by fabricators to manufacture a wide variety of products such as furniture,stair railings and farm equipment. Concrete reinforcing bar (rebar) is used to strengthen concrete in highways,bridges and buildings.

Potential Energy:

(english) The energy stored in a raised object (e.g. the weights in a grandfather clock). Potential energy equals mgh, where m is mass, g is the acceleration of gravity, and h is the vertical distance from a reference location. It is called potential energy because the energy can be regained when the object is lowered. This type of potential energy is sometimes called gravitational potential energy in order to distinguish it from elastic potential energy: see elastic energy.

Zinc

(english) Chemical Symbol Zn. Element No. 30 of the periodic system; atomic weight 65.38. Blue-white metal; when pure, malleable and ductile even at ordinary temperatures; melting point 787 (degrees) F.; boiling point 1665 (degrees) F., specific gravity 7.14. Can be electrodeposited; it is extensively used as a coating for steel and sheet zinc finds many outlets, such as dry batteries, etc. Zinc-base alloys are of great importance in die casting. Its most important alloy is brass.

Age Hardening

(english) Hardening by aging, usually after rapid cooling or cold working. The term as applied to soft, or low carbon steels, relates to a wide variety of commercially important, slow, gradual changes that take place in properties of steels after the final treatment. These changes, which bring about a condition of increased hardness, elastic limit, and tensile strength with a consequent loss in ductility, occur during the period in which the steel is at normal temperatures.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด