ผลการค้นหา

Hang Out For* *Hang Out For *Hang Out For*

ค้นเจอ 223 รายการ

Moist Room

(Concrete Engineering) A room used for storing and curing cementitious test specimens. The atmosphere of this room is maintained at a temperature of 73.4 3.0'F or 23.0*1.7'0 and relative humidity of at least 98 percent. These facilities must be adequate to continually maintain free moisture on the exteriors of test specimens.

Blasting (Blast Cleaning)

(english) A process for cleaning or finishing metal objects by use of an air blast or centrifugal wheel that throws abrasive particles against the surface of the work pieces. Small, irregular particles of steel or iron are used as the abrasive in grit blasting, and steel or iron balls in shot blasting.

ACCUMULATOR

(english) A vessel, normally cylindrical, which is used to store fluid and gas for future release of the energy in the compressed fluid and gas. Normally contains a diaphragm or piston between the fluid (liquid) and gas chambers. Fluid is normally introduced at one end and the gas at the opposite end.

Burr

(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.

Gillmore Needle

(Concrete Engineering) A device used in determining time of setting of hydraulic cement, described in ASTM 0 266. Gradation The sizing of granular materials; for concrete materials, usually expressed in terms of cumulative percentages larger or smaller than each of a series of sieve openings or the percentages between certain ranges of sieve openings.

Cellular Concrete

(Concrete Engineering) A lightweight product consisting of portland cement, cement-pozzolan, cement sand, lime-pozzolan, or lime-sand pastes, or pastes containing blends of these ingredients and having a homogenous void or cell structure, attained with gas forming chemicals or foaming agents. For cellular concretes, containing binder ingredients other than or in addition to portland cement, autoclave curing is usually employed.

Blast Furnace Slag

(Concrete Engineering) A non-metallic waste product developed in the manufacture of pig iron, consisting basically of a mixture of lime, silica and alumina, the same oxides that make up portland cement, but not in the same proportions or forms. It is used both in the manufacture of portland blast furnace slag cement and as an aggregate for lightweight concrete.

Connection:

(english) Connection is similar to the concept of support, except that connection refers to a relationship between members in a structural model. A connection restrains degrees of freedom of one member with respect to another. For each restrained degree of freedom, there is a corresponding force transferred from one member to the other; forces associated with unrestrained degrees of freedom are zero. See fixed connection and pin connection.

Boron (chemical symbol B)

(english) Element N. 5 of the periodic system. Atomic weight 10.82. It is gray in color, ignites at about 1112 (degrees) F. and burns with a brilliant green flame, but its melting point in a non-oxidizing atmosphere is about 4000 (degrees) F. Boron is used in steel in minute quantities for one purpose only- to increase the hardenability as in case hardening and to increase strength and hardness penetration.

Zinc

(english) Chemical Symbol Zn. Element No. 30 of the periodic system; atomic weight 65.38. Blue-white metal; when pure, malleable and ductile even at ordinary temperatures; melting point 787 (degrees) F.; boiling point 1665 (degrees) F., specific gravity 7.14. Can be electrodeposited; it is extensively used as a coating for steel and sheet zinc finds many outlets, such as dry batteries, etc. Zinc-base alloys are of great importance in die casting. Its most important alloy is brass.

Batch Anneal

(english) The process by which a large, stationary stack of steel coils (4 coils high) is subjected to a long heat-treating cycle. This process enables the cold-rolled sheet to fully recrystallize into the softest possible product conforming to customer specifications. Controlling the recrystallization process makes a fine-grained microstructure easy to obtain, and minimizes the tendencies for retention of directional properties of the rolled steel which could produce undesirable shapes in the stamping of a cylindrical part such as a can. Also see Anneal and Continuous Anneal.

Z-Mill

(english) The full name for z-mill is Sendzimir mill. A Z-mill operates with a very small diameter work roll, normally about 2 inches, backed up by a number of rolls in a pyramid-shaped stack. This roll set up allows you to exert extremely high forces through the work roll and yet keep the work roll from extreme flexing. The take-up roll on the Z-Mill also exerts a tension on the coil as it comes through the mill. The combination of high pressure and tension makes the mill capable of rolling material thin and flat.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด