ผลการค้นหา

ค้นเจอ 195 รายการ

Moment of inertia (I):

(english) Moment of inertia has two distinct but related meanings: 1) it is a property of a an object relating to the magnitude of the moment required to rotate the object and overcome its inertia. 2) A property of a two dimensional cross section shape with respect to an axis, usually an axis through the centroid of the shape.

Blast Furnace Slag

(Concrete Engineering) A non-metallic waste product developed in the manufacture of pig iron, consisting basically of a mixture of lime, silica and alumina, the same oxides that make up portland cement, but not in the same proportions or forms. It is used both in the manufacture of portland blast furnace slag cement and as an aggregate for lightweight concrete.

A Sheet Metal Screw

(english) Sheet metal screws with (a) sharp-pointed ends; and (b) fewer threads per inch than type AB screws; and (c) deeper threads with bettere gripping power than type AB. The industrial Fasteners Institue incorrectly labes type A an “obsolete” thread though it is universally preferred in 18-8 stainless over type AB, especially by the marine industry.

Inertial Force:

(english) A fictitious force used for convenience in visualizing the effects of forces on bodies in motion. For an accelerating body, the inertial force is considered as a body force whose resultant acts at the object's center of gravity in a direction opposite the acceleration. The magnitude of the force is the mass of the object times the magnitude of the acceleration.

Reactive waste

(Environmental Engineering) A waste which; 1) reacts violently with water, 2) forms potentially explosive mixtures with water, 3) is normally unstable, 4) contains cyanide or sulfide in sufficient quantity to evolve toxic fumes at high or low pH, 5) is capable of exploding if heated under pressure, or 6) is an explosive compound listed in Department of Transportation (DoT) regulations. One of EPA's four hazardous waste properties.

Blanking

(english) An early step in preparing flat-rolled steel for use by an end user. A blank is a section of sheet that has the same outer dimensions as a specified part (such as a car door or hood) but that has not yet been stamped. Steel processors may offer blanking for their customers to reduce their labor and transportation costs; excess steel can be trimmed prior to shipment.

Support:

(english) A support contributes to keeping a structure in place by restraining one or more degrees of freedom. In a structural model, supports represent boundary entities which are not included in the model itself, e.g., foundations, abutments, or the earth itself. For each restrained translation degree of freedom at a support, there is a corresponding reaction force; for each restrained rotation degree of freedom, there is a reaction moment.

Brinell Hardness Testing

(english) Method of determining the hardness of materials; involves impressing a hardened ball of specified diameter into the material surface at a known pressure (10-mm ball, 500-kg load for aluminum alloys). The Brinell hardness number results from calculations involving the load and the spherical area of the ball impression. Direct-reading testing are generally used for routine inspection of forgings, and as a heat treat control function.

Basic Oxygen Furnace (BOF)

(english) "WHAT A pear-shaped furnace, lined with refractory bricks, that refines molten iron from the blast furnace and scrap into steel. Up to 30% of the charge into the BOF can be scrap, with hot metal accounting for the rest. WHY BOFs, which can refine a heat (batch) of steel in less than 45 minutes, replaced open-hearth furnaces in the 1950s; the latter required five to six hours to process the metal. The BOF's rapid operation, lower cost and ease of control give it a distinct advantage over previous methods. HOW Scrap is dumped into the furnace vessel, followed by the hot metal from the blast furnace. A lance is lowered from above, through which blows a high-pressure stream of oxygen to cause chemical reactions that separate impurities as fumes or slag. Once refined, the liquid steel and slag are poured into separate containers. "

Age Hardening

(english) Hardening by aging, usually after rapid cooling or cold working. The term as applied to soft, or low carbon steels, relates to a wide variety of commercially important, slow, gradual changes that take place in properties of steels after the final treatment. These changes, which bring about a condition of increased hardness, elastic limit, and tensile strength with a consequent loss in ductility, occur during the period in which the steel is at normal temperatures.

Stiffness:

(english) This is a general term which may be applied to materials or structures. When a force is applied to a structure, there is a displacement in the direction of the force; stiffness is the ratio of the force divided by the displacement. High stiffness means that a large force produces a small displacement. When discussing the stiffness of a material, the concept is the same, except that stress substitutes for force, and strain substitutes for displacement; see modulus of elasticity.

HRM High Reactivity Metakaolin

(Concrete Engineering) Refined form of an ASTM C618, Class N (natural) pozzolan. A high performance, mineral admixture, similar in performance to silica fume, additionally comparable in cost. Pure white powdered in form will, not effect the natural color or darken concrete as silica fume does. Suitable for high-performance color matching in architectural concrete. Dosage at 5% to 10%, of cement by weight. No bleed water, better finishability, more creamy, cleanup is easier with slightly higher 28 day strengths and 25% - 35% less plasticizer is required than silica fume.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด