ผลการค้นหา

Gravity:

แปลว่า(english) An attractive force between two objects; each object accelerates at a rate equal to the attractive force divided by the object's mass. Objects near the surface of the earth tend to accelerate toward the earth's center at a rate of ; this value is often called the gravitational constant and denoted as g.

Normal strain:

แปลว่า(english) Strain measuring the intensity of deformation along an axis. Normal strain is usually denoted by . Average normal strain between two points is calculated as (Delta L / L), where L is the original distance between the points, and L is the change in that distance. Normal strain is often simply called strain.

Rotation:

แปลว่า(english) Motion of an object where the path of every point is a circle or circular arc. A rotation is defined by a point and vector which determine the axis of rotation. The direction of the vector is the direction of the axis and the magnitude of the vector is the angle of rotation.

Burr

แปลว่า(english) The very subtle ridge on the edge of strip steel left by cutting operations such as slitting, trimming, shearing, or blanking. For example, as a steel processor trims the sides of the sheet steel parallel or cuts a sheet of steel into strips, its edges will bend with the direction of the cut.

Construction Joint

แปลว่า(Concrete Engineering) The contact between the placed concrete and concrete surfaces, against or upon which concrete is to be placed and to which new concrete is to adhere, that has become so rigid that the new concrete cannot be incorporated integrally by vibration with that previously placed. Unformed construction joints are horizontally placed or nearly so.

Pumping (of Pavements)

แปลว่า(Concrete Engineering) The ejection of a mixture of water and solid materials such as clay or silt along cracks, transverse or longitudinal joints, and along pavement edges caused by downward slab movement due to the passage of heavy loads, machinery or equipment over the pavement after free water has accumulated in or on the subbase, subgrade or basecourse.

A Sheet Metal Screw

แปลว่า(english) Sheet metal screws with (a) sharp-pointed ends; and (b) fewer threads per inch than type AB screws; and (c) deeper threads with bettere gripping power than type AB. The industrial Fasteners Institue incorrectly labes type A an “obsolete” thread though it is universally preferred in 18-8 stainless over type AB, especially by the marine industry.

Blister

แปลว่า(english) 1) Coating defect consisting of the formation of bubbles in a coating, which appear as hemispherical elevations. The blisters are hollow, and are usually caused by entrapped air or solvent. 2) A raised spot on the surface on the surface of metal due to expansion of gas which causes a subsurface metal separation such as inclusions and small laminations.

Billet 2

แปลว่า(english) A solid semi-finished round or square product that has been hot worked by forging, rolling, or extrusion. An iron or steel billet has a minimum width or thickness of 1 1/2 in. and the cross-sectional area varies from 2 1/4 to 36 sq. in. For nonferrous metals, it may also be a casting suitable for finished or semi-finished rolling or for extrusion.

Vibration

แปลว่า(Concrete Engineering) Energetic agitation of concrete to assist in its consolidation, produced by mechanical oscillating devices at moderately high frequencies. (A.) External vibration employs a device attached to the forms and is particularly applicable to the manufacture of precast items and for the vibration of tunnel lining forms. (B.) Internal vibration employs an element which can be inserted into the concrete; and is more generally used for cast-in-place construction.

Blanking

แปลว่า(english) An early step in preparing flat-rolled steel for use by an end user. A blank is a section of sheet that has the same outer dimensions as a specified part (such as a car door or hood) but that has not yet been stamped. Steel processors may offer blanking for their customers to reduce their labor and transportation costs; excess steel can be trimmed prior to shipment.

Support:

แปลว่า(english) A support contributes to keeping a structure in place by restraining one or more degrees of freedom. In a structural model, supports represent boundary entities which are not included in the model itself, e.g., foundations, abutments, or the earth itself. For each restrained translation degree of freedom at a support, there is a corresponding reaction force; for each restrained rotation degree of freedom, there is a reaction moment.