ผลการค้นหา

ค้นเจอ 168 รายการ

Ball Piston Pumps

(english) The Ball Piston Pump is a very simple pump design. It has a rotor which revolves around an internal stator. The rotor has twelve cylinders machined out of it, and each cylinder has a ball inside which can slide in and out of the cylinder.

limit, liquid

ปริมาณน้ำในดินที่จุดซึ่งดินเริ่มเปลี่ยนสภาพจากของเหลวเป็นสภาพเหนียว (พลาสติก) ปั้นเป็นรูปต่าง ๆ ได้ แสดงอยู่ในรูปของเปอร์เซ็นต์โดยน้ำหนัก

Bit, Tool (cutter)

(english) A hardened steel bar or plate that is shaped accordidng to the operation to be performed and the material to be machined.

Box Annealing

(english) Annealing a metal or alloy in a sealed container under conditions that minimize oxidation. In box annealing a ferrous alloy, the charge is usually heated slowly to a temperature below the transformation range, but sometimes above or within it, and is then cooled slowly; this process is also called close annealing or pot annealing.

limit, plastic

ปริมาณน้ำในดินที่จุดซึ่งดินเริ่มเปลี่ยนสภาพจากสภาพเหนียว (พลาสติก) กลายเป็นวัสดุกึ่งแข็งหรือปริมาณน้ำที่น้อยที่สุดในดินที่ทำให้ดินสามารถถูกคลึงเป็นเส้นกลมขนาดเส้นผ่าศูนย์กลาง 3.2 ม.ม. (1/8 นิ้ว) ได้โดยไม่เกิดรอยแตกที่ผิว

Box Annealing 2

(english) A process of annealing a ferrous alloy in a closed metal container, with or without packing materials, in order to minimize the effects of oxidation. The charge is normally heated slowly to a temperature below the transformation range, but occasionally above or within it, and then is slowly cooled.

soffit, crown

จุดสูงสุดของโครงโค้ง

Bent Axis Pumps

(english) In this pump, the pistons are at an angle to the drive shaft and Thrust Plate. The piston block shaft is connected to the drive shaft by a universal joint, not shown. The drive shaft, thrust plate, piston block shaft, and piston block all revolve. The connecting rods are attached to the thrust plate and revolve with it, unlike the swash plate pump where the piston rods slide past a stationary swash plate. The outlet ports are semi-circular holes in the Valve Plate, shown on the far right of the animation on edge and in a head-on view below, right. As the pump revolves, half the pistons suck in fluid as they pass over the intake port. The other pistons discharge their fluid through the outlet port. This pump should be compared to the radial piston pump, swash plate pump, and wobble pump.

Cold Joint

(Concrete Engineering) A visible lineation which forms when the placement of concrete is delayed. The concrete in place hardens prior to the next placement of concrete against it.

Age Hardening

(english) Hardening by aging, usually after rapid cooling or cold working. The term as applied to soft, or low carbon steels, relates to a wide variety of commercially important, slow, gradual changes that take place in properties of steels after the final treatment. These changes, which bring about a condition of increased hardness, elastic limit, and tensile strength with a consequent loss in ductility, occur during the period in which the steel is at normal temperatures.

Blast Cleaning (blasting)

(english) A process for cleaning or finishing metal objects by use of an air jet or centrifugal wheel that propels abrasive particles (grit, sand, or shot) against the surfaces of the workpiece at high velocity.

Vapor Pressure

(Concrete Engineering) The pressure exerted by a vapor that is calculated based upon relative humidity and temperature. The higher the humidity and higher temperature, in degrees Fahrenheit, the greater the vapor pressure exerted.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด