ผลการค้นหา

Carbonation

แปลว่า(Concrete Engineering) 1) Reaction between the products of portland cement (soluble calcium hydroxides), water and carbon dioxide to produce insoluble calcium carbonate (efflorescence). 2) Soft white, chalky surface dusting of freshly placed, unhardened concrete caused by carbon dioxide from unvented heaters or gasoline powered equipment in an enclosed space. 3) Carbonated, dense, impermeable to absorption, top layer of the surface of concrete caused by surface reaction to carbon dioxide. This carbonated layer becomes denser and deeper over a period of time. 4) Reaction with carbon dioxide which produces a slight shrinkage in concrete. Improves chemical stability. Concrete masonry units during manufacturing may be deliberately exposed to carbon dioxide after reaching 80% strength to induce carbonation shrinkage to make the units more dimensionally stable. Future drying shrinkage is reduced by as much as 30%.

Unit Water Content

แปลว่า(Concrete Engineering) The quantity of water per unit volume of freshly mixed concrete, often expressed as gallons or pounds per cubic yard. This is the quantity of water on which the water cement ratio is based, and does not include water absorbed by the aggregate

Cell

แปลว่า(Environmental Engineering) A unit of varying dimensions in a landfill which is isolated from the environment by 6 to 12 inches of soil cover. A cell is one day's waste or less. A cell is covered with soil at the end of each day.

Ductility:

แปลว่า(english) Ductility generally refers to the amount of inelastic deformation which a material or structure experiences before complete failure. Quantitatively, ductility can be defined as the ratio of the total displacement or strain at failure, divided by the displacement or strain at the elastic limit.

Blow Back

แปลว่า(english) A coating defect consisting of a lower coating film weight on the bottom of the coated sheet caused by high velocity air in the oven. Blow back usually occurs with high solids coatings which have little solvent to evaporate and "set" the film.

Blue Brittleness

แปลว่า(english) Brittleness exhibited by some steels after being heated to some temperature within the range of 300 (degrees) to 650 (degrees) F, and more especially if the steel is worked at the elevated temperature. Killed steels are virtually free of this kind of brittleness.

GFRC - Glass Fiber Reinforced Concrete

แปลว่า(Concrete Engineering) Concrete panels, usually architectural designs, reinforced with a high zirconia (16% minimum), alkali-resistant glass fiber. Optimum glass fiber content of 5% by weight. Lower fiber content results in lower early ultimate strengths, higher fiber content can produce composite compaction and consolidation difficulties.

Modulus of elasticity:

แปลว่า(english) The proportional constant between stress and strain for material with linear elastic behavior: calculated as stress divided by strain. Modulus of elasticity can be interpreted as the slope of the stress-strain graph. It is usually denoted as E, sometimes known as Young's Modulus Y, or E-Modulus.

Flexibility:

แปลว่า(english) Flexibility is the inverse of stiffness. When a force is applied to a structure, there is a displacement in the direction of the force; flexibility is the ratio of the displacement divided by the force. High flexibility means that a small load produces a large displacement.

Bloom 2

แปลว่า(english) A semi-finished hot rolled product, rectangular in cross section, produced on a blooming mill. For iron and steel, the width is not more than twice the thickness, and the cross-sectional area is usually not less than 36 sq. in. Iron and steel blooms are sometimes made by forging.

Abrasive 1

แปลว่า(english) Material for grinding, polishing, blasting, either in loose form or bonded to form wheels, bricks, or files, or applied to paper and cloth by glue or resin. Natural abrasives include emery, corundum, garnet, sand, flint, etc. Metallic shot and grit are also used as abrasives in cleaning castings

Bundle

แปลว่า(english) Specific number of sheets which equals 1 unit of production. Number is determined by multiplying sheets/Packages/BUNDLE. For example, an order calls for 112 sheets/package. According to the maximum height allowed for a lift. Therefore, multiplying 15 packages X 112 sheets 3D 1680 sheets/bundle.