ผลการค้นหา

ค้นเจอ 174 รายการ

Basic Oxygen Process

(english) (BOP) A process in which molten steel is produced in a furnace by blowing oxygen into molten iron, scrap and flux materials. The furnace is known as Basic Oxygen Furnace (BOF).

Vapor Pressure

(Concrete Engineering) The pressure exerted by a vapor that is calculated based upon relative humidity and temperature. The higher the humidity and higher temperature, in degrees Fahrenheit, the greater the vapor pressure exerted.

Brown Sharp Gages

(english) A standard series of sizes refered to by numbers, in which the diameter of wire or thickness of sheet metal is generally produced and which is used in the manufacture of brass, bronze, copper, copper-base alloys and aluminum. These gage numbers have a definite relationship to each other. In this system, the decimal thickness is reduced by 50% every six gage numbers- while temper is expressed by the number of B&S gage numbers as cold reduced in thickness from previous annealing. For each B&S gage number in thickness reduction, where is assigned a hardness value of 1/4 hard.

Agglomerating Processes

(english) "Fine particles of limestone (flux) and iron ore are difficult to handle and transport because of dusting and decomposition, so the powdery material usually is processed into larger pieces. The raw material's properties determine the technique that is used by mills. 1) SINTER Baked particles that stick together in roughly one-inch chunks. Normally used for iron ore dust collected from the blast furnaces. 2) PELLETS Iron ore or limestone particles are rolled into little balls in a balling drum and hardened by heat. 3) BRIQUETTES Small lumps are formed by pressing material together. Hot Iron Briquetting (HBI) is a concentrated iron ore substitute for scrap for use in electric furnaces.

Abrasion 1

(english) The displacement and/or detachment of metallic particles from a surface as a consequence of being exposed to flowing solids, fluids or gases. The process of rubbing, grinding, or wearing away by friction.

Consolidation

(Concrete Engineering) Compaction usually accomplished by vibration of newly placed concrete to minimum practical volume, to mold it within form shapes and around embedded parts and reinforcement, and to eliminate voids other than entrained air.

Blast Cleaning (blasting)

(english) A process for cleaning or finishing metal objects by use of an air jet or centrifugal wheel that propels abrasive particles (grit, sand, or shot) against the surfaces of the workpiece at high velocity.

Brazing

(english) Joining metals by fusion of nonferrous alloys that have melting points above 800 F (425C), but lower than those of the metals being joined. May be accomplished by a torch. Filler metal is ordinarily in rod form in torch brazing; whereas in furnace and dip brazing the work material is first assembled and the filler metal may then be applied as wire, washers, clips, bands, or may be bonded, as in brazing sheet.

Bottle Top Mold

(english) Ingot mold, with the top constricted; used in the manufacture of capped steel, the metal in the constriction being covered with a cap fitting into the bottle-neck, which stops rimming action by trapping escaping gases.

Wetland

(Environmental Engineering) Semi-aquatic land, that is land that is either inundated or saturated by water for varying periods of time during each year, and that supports aquatic vegetation which is specifically adapted for saturated soil conditions.

BETA RATIO (#)

(english) The amount, expressed as a ratio, of particles in a fluid stream upstream of a filter, after the fluid posses through a filter, divided by the amount of particles downstream, for a particular size particle.

Couple:

(english) A system of forces composed of two equal forces of opposite direction, offset by a distance. A couple is statically equivalent to a moment whose magnitude equals the magnitude of the force times the offset distance.

ศัพท์ช่างภาษาอังกฤษ – ไทย จัดกลุ่มตามตัวอักษร A-Z

ดูหมวดหมู่ทั้งหมด