ผลการค้นหา

Irreversible reaction

แปลว่า(Environmental Engineering) A reaction in which the reactant(s) proceed to product(s), but the products react at an appreciable rate to reform reactant(s).

ACCUMULATOR

แปลว่า(english) A vessel, normally cylindrical, which is used to store fluid and gas for future release of the energy in the compressed fluid and gas. Normally contains a diaphragm or piston between the fluid (liquid) and gas chambers. Fluid is normally introduced at one end and the gas at the opposite end.

Gravity:

แปลว่า(english) An attractive force between two objects; each object accelerates at a rate equal to the attractive force divided by the object's mass. Objects near the surface of the earth tend to accelerate toward the earth's center at a rate of ; this value is often called the gravitational constant and denoted as g.

Moist Room

แปลว่า(Concrete Engineering) A room used for storing and curing cementitious test specimens. The atmosphere of this room is maintained at a temperature of 73.4 3.0'F or 23.0*1.7'0 and relative humidity of at least 98 percent. These facilities must be adequate to continually maintain free moisture on the exteriors of test specimens.

Aging 2

แปลว่า(english) A change in properties that occurs at ambient or moderately elevated temperatures after hot working or a heat treating operation (quench aging in ferrous alloys), or after a cold working operation (strain aging). The change in properties is often, but not always, due to a phase change (precipitation), but does not involve a change in chemical composition. In a metal or alloy, a change in properties that generally occurs slowly at room temperature and more rapidly at higher temperatures.

Agglomerating Processes

แปลว่า(english) "Fine particles of limestone (flux) and iron ore are difficult to handle and transport because of dusting and decomposition, so the powdery material usually is processed into larger pieces. The raw material's properties determine the technique that is used by mills. 1) SINTER Baked particles that stick together in roughly one-inch chunks. Normally used for iron ore dust collected from the blast furnaces. 2) PELLETS Iron ore or limestone particles are rolled into little balls in a balling drum and hardened by heat. 3) BRIQUETTES Small lumps are formed by pressing material together. Hot Iron Briquetting (HBI) is a concentrated iron ore substitute for scrap for use in electric furnaces.

Tilt-up

แปลว่า(Concrete Engineering) A method of concrete construction such as where members are cast horizontally near their eventual position, usually on a recently placed slab, and then tilted into place after removal of forms.

Support:

แปลว่า(english) A support contributes to keeping a structure in place by restraining one or more degrees of freedom. In a structural model, supports represent boundary entities which are not included in the model itself, e.g., foundations, abutments, or the earth itself. For each restrained translation degree of freedom at a support, there is a corresponding reaction force; for each restrained rotation degree of freedom, there is a reaction moment.

Hindered (Zone) settling

แปลว่า(Environmental Engineering) Settling in which particle concentrations are sufficient that particles interfere with the settling of other particles. Particles settle together as a body or structure with the water required to traverse the particle interstices.

Baseline

แปลว่า(Software Engineering) a point at which some deliverable produced during the software engineering process is put under formal change contro เส้นอ้างอิง ใช้สำหรับการวางผัง หรือการสำรวจ

Bainite

แปลว่า(english) A eutectoid transformation product of ferrite and a fine dispersion of carbide, generally formed at temperatures below 840 to 930 F (450 to 500 C): upper bainite is an aggregate containing parallel lath-shape units of ferrite, produces the so-called feathery appearance in optical microscopy, and is formed at temperatures above about 660 F (350 C); lower bainite consists of individual plate-shape units and is formed at temperatures below about 660 F (350 C). Also, a slender, needle-like (acicular) microstructure appearing in spring steel strip characterized by toughness and greater ductility than tempered Martensite. Bainite is a decomposition product of Austenite best developed at interrupted holding temperatures below those forming fine pearlite and above those giving Martensite.

Brinell Hardness Testing

แปลว่า(english) Method of determining the hardness of materials; involves impressing a hardened ball of specified diameter into the material surface at a known pressure (10-mm ball, 500-kg load for aluminum alloys). The Brinell hardness number results from calculations involving the load and the spherical area of the ball impression. Direct-reading testing are generally used for routine inspection of forgings, and as a heat treat control function.